Posts Tagged ‘EAPoverUDP’

I’ve always said that, when it comes to Cisco, my brains go boom, temperature increases and I end up having 30 Firefox tab trying to search on what on earth some kinky cisco-ish feature does and _how_ precisely.

After the latest IPsec adventure with Cisco’s Customer Support (CCIE Security) which advised me to run commands that were not even available on my IOS (yes, I had previously given them my config and IOS version), I said that whenever I have Cisco-related issues I go straight to my team lead, the guy being able to fix no matter issue I encountered on Cisco – at least on the IPsec side…

Now, I’ve had the honor of having to move an EoU/WebAuth config from a 3750 to a 6500. While I was feeling pretty good about myself being able to configure and understand the way to configure EoU and WebAuth on Cisco (EoU is NAC L2, I am using L2 interfaces in a L2 vlan in mode access and use the “ip admission” command on the L2 interface, while WebAuth gets configured as a fallback to 802.1x using the “dot1x fallback dot1x-www” on the L2 interface), I have now realized that I am FAR FAR AWAY from the truth. I’ve woken up on this twisted 6500, where I have the possibily of configuring:

1. 802.1x – fair enough, I am not using 802.1x here anyways

2. NAC Layer 2 IP / LAN Port IP – which can be configured this way (as per Cisco’s KB)

Router# configure terminal
Router(config)# ip admission name nac eapoudp
Router(config)# access-list 5 permit any any
Router(config)# interface gigabitethernet 2/0/1
Router(config-if)# ip access-group 5 in
Router(config-if)# ip admission nac
Router(config-if)# exit
Router(config)# aaa new-model
Router(config)# aaa authentication eou default group radius
Router(config)# radius-server host admin key rad123
Router(config)# radius-server vsa send authentication
Router(config)# ip device tracking probe count 2
Router(config)# eou logging
Router(config)# end

3. LAN Port IP – which, ignoring their own definition from some KBs, now appears as a “Web-Based Authentication” and gets configured…nowhere says _how_

4. NAC Layer 3 IP / NAC Gateway IP – which should be enabled on L3 interfaces

Router(config)# ip admission name webauth1 proxy http

Router(config)# interface fastethernet 5/1

Router(config-if)# ip admission webauth1

Router(config-if)# authentication order webauth

Router(config-if)# exit

Router(config)# ip device tracking

Router(config)# ip admission proxy http login page file disk1:login.htm

Router(config)# ip admission proxy http success page file disk1:success.htm

Router(config)# ip admission proxy http fail page file disk1:fail.htm

Router(config)# ip admission proxy http login expired page file disk1:expired.htm

5. NAC Gateway IP – which is configured as auth-proxy, this way:

Router(config)# ip auth-proxy name webauth http inactivity-time 60

Router(config)#interface GigabitEthernet3/15

Router(config-if)# description WEBAUTH

Router(config-if)# switchport

Router(config-if)# switchport access vlan 502

Router(config-if)# switchport mode access

Router(config-if)# ip access-group www in

Router(config-if)# spanning-tree portfast edge

Router(config-if)# ip auth-proxy webauth

Router(config)# ip access-list extended www

Router(config)# permit tcp any any eq www

Router(config)# deny   ip any any

The “aaa authentication login default radius” is on. The “ip http server” is on. The “aaa authorization auth-proxy default group radius ” is on also.

Now, I am no EoU, WebAuth, and by far no Cisco guru, but, what gives? Why so many auth methods? And, specially, why the method I use to configure one way on a 3750 (WebAuth using the “auth-proxy” set of commands) is configured some other way on 6500 (WebAuth using the “ip admission <name> proxy http” set of commands) – while keeping the “auth-proxy” set of commands – which here do something else. Why is it so hard to be consistent all over your own set of devices?

I have done 802.1x on Summit (netlogin called in there), WebAuth on Summit and WebAuth on HP switches. None of them seemed so damn confusing 😦 I am lost.